thunderdome
slotcar
Raceway
Presents
2006 Queensland
slotcar
Championship
10th, 11th &12th of
November 2006
The race in rocky
The Track:
155 ft. blue king right hand braid is positive in the direction of travel is wire positive gate and braid is recessed .020 from the surface.
Standard extension lead plug on controller same as NSW and VIC
Power:
Track is powered by 4x200 amp batteries and 2 x 55amp Rivergate bulldog power supplies providing smooth constant power, track has nine power taps.
Track surface:
Surface is blue in colour and very smooth
Track Washing:
In an effort to hopefully set some very fast times and high lap total the straights will be washed after INT 15 and between heats of GP27 and GP7
Cash Prize:
We are offering $300.00 cash money for the first person to go 1.699 or better, we believe the track is up to it and our money is at serious risk.
More Info:
For more information about this annual event please contact us by phone (07) 49220585
Or email Thunderdome@dodo.com.au
Regards Carl
Race Procedure
Qualifying
Qualifying will be run in the reverse order of entry. Each entrant will be given a timed run to record their fastest lap which will determine their starting order in the heats. See class rules for details of time allowed.
Format
All entrants will consist of a series of consies, heats quarterfinals, semi-finals, final dependent on the number of entries.
All races designated as consies will be contested over 4 lanes only, running on either the red set i.e. red, green, blue, purple, or on the black set black, yellow, orange, white. All other races will be contested over 8 lanes.
All races will be on a move up basis. The following schedule has been adopted to ensure that a minimum of 4 drivers will move up from each race. See class rules for heat and lane change times.
1to 8 entries: Final only
9 Entries: One heat and final, fastest qualifier into final top 7 move up.
10 to 16 Entries: Two semis and final top 4 from each semi move up.
17 to 20 Entries: One heat, two semis and final. Fastest 12 qualifiers into semis top 4 in heat move up.
21 to 24 Entries: Two heats, two semis and final. Fastest 8 qualifiers into semis top 4 in each heat move up.
25 to 32 Entries: Four quarterfinals, two semis and final. All entrants start in quarterfinals top 4 in each move up.
33 to 36 Entries: one consie, four quarterfinals, two semis, and final. Fastest 28 into quarterfinals top 4 in consie move up
37 to 40 Entries: Two consies, four quarterfinals, two semis, and final. Fastest 24 into quarterfinals top 4 in each consie to move up.
40+ Entries: Fastest 16 into quarterfinals. All other drivers will be seeded into number of consies with the top 4 lap scorers in each consie to move up to the next stage of the race schedule.
Lane choice will be determined by qualifying position or position from previous heat.
Lap counter
The Johnson Racing Systems computer [Version 3.0] will be used for all events; this system incorporates the following unique features which drivers must be aware of.
Rider detection. The system will implement an automatic track call if it detects a lap time shorter than a pre-programmed time delay and the lap is not counted This time delay is set to 1/10th of a second shorter than the fastest qualifier. Cars which cross the lap counter on the wrong lane causing such a track call will be replaced on the correct lane immediately before the counter, thereby eliminating any lost or gained laps. Drivers should be aware that the system treats every bracket as a continuation of the preceding bracket. Therefore if the car is moved forward on the track during a lane change it will trigger a short lap track call when it crosses the counter. If this should occur then the offending car will not be credited with the lap and will restart from where it stopped. This is effectively a one lap penalty for cheating on the lane change.
Time factor
At the end of the last bracket for each race all cars must continue until they cross the lap counter. As each car crosses the lap counter the power is turned off on their lane by the computer this eliminates the need for footages and means that all positions on the computer are correct at the end of racing. Each car is given a time factor which is the time from when the bracket expired to when the car crossed the lap counter [accurate to 1/1000th of a second]. Drivers must be aware that the race does not end until they cross the lap counter or a maximum of 10 seconds expirees.
Track calls
Track calls
will only occur in the following circumstances- Automatic rider track call; Cars
off in the main straight or the bank; Unmarshalable car; A marshal has to many
cars to cope with; Marshal not in position ; track fault. It is the
intention of the race director to maintain fair racing at all times
GENERAL RULES
Race Entry
Entries for all classes will be accepted from 11.30 Friday 10th November
Drivers may compete in any or all events
An entrant shall be deemed to consist of one driver and one car. The entrant having paid their entry fees for an event shall comply with the regulations as set down and abide by the decision of the race director.
Cars and scrutineering
Cars must comply with the specifications for their class and any relevant general rules at all times while racing
All repairs and replacement parts must comply with the specifications for their class.
Any component may be replaced with the exception of chassis or body.
Cars will be inspected before qualifying and prior to all finals.
After preliminary inspection all cars will be impounded.
All cars moving up will be impounded after consie, heat, q/final, and semi.
Any car may undergo a tear down inspection after racing.
The scrutineers interpretation of the rules shall be final. The scrutineer is also empowered to rule on any area of the cars construction not specifically covered by the rules.
Controllers and driving
Any controller device may be used as long as it does not increase voltage to the track. The race director may inspect controllers at his discretion.
Any device deemed to interfere with the track computer system shall be banned from the event.
Only the driver may operate any device that controls their car on the track. There must be no outside assistance in the operation of controllers or chokes etc.
Drivers must stand at the control panel for their lane when driving.
Only drivers in the current race will be allowed at the drivers panel.
*** Special consideration will be given to disabled drivers.
Drivers conduct
Drivers and
their pit crews are expected to conduct themselves in professional manner at all
times. Abusive, offensive or unsportsmanlike like conduct will result in
immediate penalties being imposed.
Drivers are warned they are responsible for the conduct of their pit crews.
Marshalling
The race director will advise Drivers of their marshalling duties. Failure to perform required duties will result in a penalty Drivers who are unable to marshal due to a disability are required to nominate an acceptable substitute.
Penalties
If required,
the race director will apply penalties for rule infractions.
Penalties may range from warnings to exclusion from the event.
Black flag
The race director will demand the removal from the track of any car which is dragging on the track, interfering with other cars or continually deslotting. The car may be repaired and returned to the track.
Guide and lead wire
Only one guide per car.
Guide clips may be used.
Any lead wire may be used.
Front wheels
All cars must be fitted with two front wheels located in the normal position.
Must be equipped with rubber type tyres. (Full rubber type wheels are acceptable on wing cars only)
Must contact the track surface before any part of the chassis when the car is rocked from side to side.
Minimum diameter .500 for all classes.
Rear wheels
Any colour/compound rear wheels may be used.
Bodies
An entrant may only use one body per class. Air control devices may be replaced if damaged during racing.
All bodies must be commercially available.
Bodies must cover the entire chassis and the guide. No parts may protrude other than rear tyres.
Where a particular body or range of bodies is specified must not be cut above the manufactures intended cut line.
Bodies must be painted to appear opaque with the exception of windows, which must be left clear. Front wheel arches must also be left clear or cut so that front wheels are clearly visible.
Interiors, where required must be painted a minimum of three colours so as to maintain an appearance of realism and be of the correct scale and size to cover the entire inside of the car front to rear side to side.
Bodies may be reinforced with tape and /or other suitable materials.
Air controls devices must be clear or translucent although stickers, stripes and tape may be added.
Front edges of side dams should be taped to avoid injury to marshals and spectators.
Maximum Height (wing cars) 63.5mm. Maximum length front diaplane 12.7 mm
Diaplanes on GP10 or GP12 GTP/WSC must not protrude beyond original bodywork.
Track clearance and width
Class Track clearance Width
Group 10 sedans 0.047 85mm
Group 12 GTP 0.047 85mm
Group 12 wing car 0.062 83mm
INT 15 0.062 83mm
GP27 0.062 83mm
GP7 0.062 83mm
Gooing
Sedan classes (GP10, GP12 sedans) the track will be conditioned by the race director prior to commencement of racing. And as deemed necessary between races. No other traction compound may be added to the track. It has been found that the use of natural rubber compounds leads to a build up of rubber on the track, which can make racing most unpredictable. If this should occur the race director may choose to clean and condition the affected area between races.
Wing classes (GP12 wing car) as per sedan rules. (INT 15, GP27, GP7) Traction compounds may be added to the track in designated zones only before racing and during the lane changes. Rolling or padding traction compound beyond the designated zone will be permitted. Traction compound may be removed during racing but only by the driver. Care must be taken not to interfere with other cars on other lanes.
EVENT TIMETABLE
FRIDAY 10TH OF NOVEMBER
11.30 AM Raceway opens for practice
6.30PM Entries for 16 D touring cars close /scrutineering
6.45PM Qualifying
7.00PM Race starts
SATURDAY 11TH OF NOVEMBER
9.00 AM Raceway opens practice
10.30 AM Entries close super 16 D GTP/scrutineering
10.45 AM Qualifying super 16 D
11.00 AM Race starts
1.30 PM Entries close GTP 12 /scrutineering
1.45 PM Qualifying GTP 12
2.00 PM Race starts
4.00 PM Race way spray glued for GP 12 wing cars
5.00 PM Entries close GP12 wing car / scrutineering
5.15 PM Qualifying
5.30 PM Race starts
7.30 PM Raceway cleaned and spray glued for wing car practice
10.30
PM Raceway closed
SUNDAY 12TH OF NOVEMBER
9.00 AM Raceway opens practice
10.00 AM Entries close INT15 / scrutineering
10.15 AM Qualifying
10.30 AM Race starts
12.00 NOON Entries close GP27 wing car /scrutineering
12.15 PM Qualifying
12.45 PM Race starts
4.00 PM Entries close GP7 wing car / scrutineering
4.15 PM Qualifying
5.00 PM Race starts
10.30 PM Raceway closed
16D Touring car Specifications
Entry fee $15.00
Race duration
Qualifying 1 minute / no byes - Power 14 volts
Consie 2 minute / 1minute lane change
Heats 2minute / 1 minute lane change
Quarter final 2 minute / 1 minute lane change
Semi-final 2minute / 1minute lane change
Final 3 minute / 90 second lane change
Body
Permitted bodies - Sunset VS. Commodore, .EL. Falcon
Must have full interior, driver must be painted a minimum of three colours.
Chassis
Any commercially available pressed steel group 10 type chassis may be used. All original dimensions, mounting points and basic configuration must be retained with the following exceptions. - NO alum side pans
Plating may be removed to facilitate soldering of chassis parts.
Rear axle tube and /or wire brace may be added. Motor may be soldered in place.
Rear axle height may be altered proved no material other than plating is removed.
Body tape may be used to aid in chassis performance.
Front axle maximum diameter 0.062
Front wheel retainers may be substituted or soldered in place.
Front axle may be soldered in place or braced to prevent rotation.
Rear axle
1/8 solid only
Oilite type bushings only may be glued or soldered in place.
Gears
Any unmodified 48 D.P. gears.
Motor
Parma 500,501, 502 standard, Deathstar
Parma 498 IX rotor setup or Fastones AT midnight setups are permitted.
Must use all original hardware including endbell, brush hoods buss bars and spring posts.
Endbell and hardware may not be modified in any way with the exception of honing of the hoods to take big foot brushes.
Only endbell to can screws may be added or substituted.
Can may not be modified except for the following.
Notching for axle clearance.
Removal of paint or plating to facilitate soldering.
Oilite hole may be centered and can may be straightened.
Oilite type bushing only may be glued or soldered in place.
Magnets must be of original type for set up must be located by original retainers a small amount of glue will be permitted to stop forward and aft movement of the magnet.
Magnets may be remagnetised.
Any springs and brushes may be used.
Shunt wire and insulation is not permitted.
Armature
Only Parma 501-A Deathstar type armature will be permitted com truing and dying of stacks will be permitted. Armature spacers are allowed. NO after market blue printed armatures will be permitted i.e. Proslot, RJR/Viper Fastones or Parma American made PSE armatures.
SUPER 16D GTP SPECIFICATIONS
Entry fee $15.00
Race duration
Qualifying 1 minute / no bye - Power 14 volts
Consie 2 minute bracket / 90 second lane change
Heat 2 minute bracket / 90 second lane change
Quarter final 2 minute bracket / 90 second lane change
Semi final 2 minute bracket / 90 second lane change
Final 3 minute bracket / 2 minute lane change
Body
Sunset Porsche extreme are the only permitted body.
Must have full interior painted minimum of three colours No wing car interiors.
Chassis
Any commercially available group 10 pressed steel type chassis. All original dimensions and mounting points and basic configuration must be retained with the following exceptions:-
Alum side pans will be permitted
Plating may be removed to facilitate soldering of chassis parts.
Rear axle tube and /or wire brace may be added. Motor may be soldered in place.
Rear axle height may be altered proved no material other than plating is removed.
Body tape may be used to aid in chassis performance.
Front axle maximum diameter 0.062
Front wheel retainers may be substituted or soldered in place.
Front axle may be soldered in place or braced to prevent rotation.
Rear axle
1/8 solid only
Oilite type bushings only may be glued or soldered in place.
Gears
Any unmodified 48 D.P. gears.
Motor
Parma 500,501, 502 standard, Deathstar
Parma 498 IX rotor setup or Fastones AT midnight setups are permitted. P/slot FX setup
Must use all original hardware including endbell, brush hoods buss bars and spring posts.
Endbell and hardware may not be modified in any way with the exception of honing of the hoods to take big foot brushes.
Only endbell to can screws may be added or substituted.
Can may not be modified except for the following.
Notching for axle clearance.
Removal of paint or plating to facilitate soldering.
Oilite hole may be centered and can may be straightened.
Oilite type bushing only may be glued or soldered in place.
Magnets must be of original type for set up must be located by original retainers a small amount of glue will be permitted to stop forward and aft movement of the magnet.
Magnets may be remagnetised.
Any springs and brushes may be used.
Shunt wire and insulation is not permitted.
Armature
Permitted Armatures any Parma, PSE, Pro-slot, RJR/Viper Super 16 D armature with a minimum stack length of .490and minimum diameter of .520 and 60 series wound turns of 28 gauge [AWG] wire. Armature spacers and com truing permitted.
GROUP 12 GTP SPECIFICATIONS
Entry fee $15.00
Race Duration
Qualifying 1 minute / no byes - Power 14 V
Consie 2 minute bracket / 90second lane change
Heats 2 minute bracket / 90second lane change
Quarter final 2 minute bracket / 90second lane change
Semi final 2 minute bracket / 90second lane change
Final 3 minute bracket / 2minute lane change
Body
Permitted bodies are PSE Lola Hi -down force 70524,
PSE Caddy 70525,
PSE Caddy 70526 Hi -down force
GT 305 Caddy Hi -down force
GT 296 Lola Hi-down force
Driver must be painted a minimum of three colours.
Chassis
Any group 12 sedan type chassis NO wing car chassis will be permitted.
Gears Any
Rear axle
Any 3/32 or 1/8 solid only. Oilite bushings only may be glued or soldered in place
Motor
Any mass produced full size c/can set up. No strap cans
Any mass produced c/can endbell except those made for from a metal or alloy of metals.
Must use original brush hoods and buss bars, spring post may be substituted.
Endbell and hardware may not be modified in any way
Endbell to can and hardware screws may be added and or substituted.
Can may not be modified in any way except for the following.
Notching for axle clearance.
Removal of paint to facilitate soldering
Oilite hole may be centered.
A small hole may be drilled in each side of the can to aid in the gluing of magnets (2mm max)
Oilite bushing only in endbell
Bearing permitted in can
Any full can height, single piece ceramic magnet may be used. [No quads Except for Proslot SMQ]
Magnets may not contain rare earth materials defined as elements with the atomic weight 58 through 71.
Magnets may be glued, shimmed, radiused and polished.
Any brushes and springs may be used.
Shunt wire and insulation may be used.
Any tagged X-12 or X12+ armature with a minimum stack length of 0.350 and minimum50 series wound turns of 29 gauge [AWG wire may be used.
Minimum armature diameter 0.512
Armature spacers may be used.
GROUP 12 WING CAR SPECIFICATIONS
Entry fee- $20.00
Race duration
Qualifying 2 minute/ bye round 30 second penalty Power 16 volts/Race 14 V
Consie 2 minute bracket / 1 minute lane change
Heat 2 minute bracket / 1minute lane change
Quarter final 2 minute bracket / 1minute lane change
Semi final 2 minute bracket / 90 second lane change
Final 3 minute bracket / 3minute lane change
Body
Any winged body. Interiors are required PSE wing car interior are permitted.
See general rules bodies
Chassis
Any commercially available except chassis or chassis components cut from aluminum alloy
Car weight
Minimum car weight 72 grams.
Rear Axle
3/32 solid axle only, flats for grub screws permitted, no titanium or hollows allowed.
Oilite bushings only may be glued or soldered in place.
Gears
Any
Motor
Any mass produced full size c/can set up. No strap cans
Any mass produced c/can endbell except those made for from a metal or alloy of metals.
Must use original brush hoods and buss bars, spring post may be substituted.
Endbell and hardware may not be modified in any way
Endbell to can and hardware screws may be added and or substituted.
Can may not be modified in any way except for the following.
Notching for axle clearance.
Removal of paint to facilitate soldering
Oilite hole may be centered.
A small hole may be drilled in each side of the can to aid in the gluing of magnets (2mm max)
Oilite bushing only in endbell
Bearing permitted in can
Any full can height, single piece ceramic magnet may be used. [No quads Except for Proslot SMQ]
Magnets may not contain rare earth materials defined as elements with the atomic weight 58 through 71.
Magnets may be glued, shimmed, radiused and polished.
Any brushes and springs may be used.
Shunt wire and insulation may be used.
Any tagged X-12 or X12+ armature with a minimum stack length of 0.350 and minimum50 series wound turns of 29 gauge [AWG wire may be used.
Minimum armature diameter 0.512
Armature spacers may be used.
INT 15 WING CAR SPECIFICATIONS
Entry fee $25.00
Race duration
Qualifying 2 minute / bye round 30 second penalty - Power 16 volts / Race 14V
Consie 2 minute bracket / 2 minute lane change
Heats 2 minute bracket / 2 minute lane change
Quarter final 2 minute bracket / 2 minute lane change
Semi final 2 minute bracket / 2 minute lane change
Final 3 minute bracket / 3 minute lane change
Body
Any winged body. Interiors are required PSE wing car interiors are permitted.
See general rules Bodies
Chassis- Any
Rear axle- Any
Gears- Any
Motor
Any mass produced strap or u bend type cans are permitted.
Minimum internal width .835
Cut out and machine work are permitted.
Any ceramic magnets may be used Rare earth materials are forbidden.
Magnets may be shimmed, glued, radiused and polished.
Any endbell and hardware may be used.
Endbell to can mounting screws may be added and / or substituted.
Any brushes and springs may be used.
Shunt wire and insulation are permitted.
Any bearings allowed. May be soldered or glued in place.
Any machine wound, tagged 15 or INT15 armature with a minimum stack length of .440 and a minimum of 50 series wound turns of 29 gauge [AWG] wire may be used.
Armature spacers may be used.
GROUP 27 SPECIFICATIONS
Entry fee- $25.00
Race duration
Qualifying 2 minute / bye round 30 second penalty Power 16 volts / Race 14 V
Consie 2 minute bracket / 2minute lane change
Heat 2 minute bracket / 2 minute lane change
Quarter final 2 minute bracket / 2minute lane change
Semi final 2 minute bracket / 2 minute lane change
Final 4 minute bracket / 4 minute lane change
Body
Any winged body interiors are required PSE wing car interiors permitted.
See general rules -bodies
Chassis- Any
Rear axle - Any
Gears - Any
Motor - Any set up may be used
Any tagged armature with a minimum stack length 0.440 and a minimum of 38 series wound turns of 27 gauge [AWG] wire may be used.
GP 7 Open Specifications
Entry fee- $30.00
Race duration
Qualifying 2 minute / bye round 30 second penalty Power 16 volts / Race 14 V
Consie 2 minute bracket / 2 minute lane change
Heat 2 minute bracket / 2 minute lane change
Quarter final 2 minute bracket / 2 minute lane change
Semi final 2 minute bracket / 2 minute lane
Final 5 minute bracket / 4 minute lane change
Body
Any winged body interiors required PSE wing car interiors permitted.
See general rules Bodies
Chassis - Any
Rear axle- Any
Gears- Any
Motor- Any
Accommodation
O'Dowd's Irish Pub
100 William Street
(07)49270344
2 min walk
Single room from $40.00
Backpacker rooms sleeps 4 $20.00 per bed
----------------------------------------
Criterion Hotel
150 Quay Street
(07) 49221225
10 min walk
Period hotel rooms for four $80.00
----------------------------------------
City Walk Motor Inn
129 William Street
(07) 49226009
10 min walk
Triple room: - 1 double bed 1 single $75.00
Inc Cont. breakfast
-----------------------------------------
Oxford Hotel
East Street
(07) 49221837
2 min walk
Backpacker type room
Sleeps 2 or 4 $19.50 per person
------------------------------------------
The Heritage Tavern
234 Quay Street
(07) 49276996
2 min walk
-------------------------------------------
Backpacker rooms
Sleeps 4 $20.00 per bed
Sleeps 2 $30.00 per bed
Single $45.
------------------------------------------